23 Giugno 2018


code: E-PRS - Radar Simulators
The most common way used to evaluate the effects of ECM systems is a test range that involves several ships or airplanes in an operational environment.
This method is very expensive and most of the time real platforms are unavailable. On the other hand, using software simulation only, it is often not so clear the real effect of the ECM System Under test on enemy Radars. In fact, only a "Hardware In the Loop" Simulation System can represent the reality with a reasonable accuracy.
E-PRS, the natural evolution of the former GRS (Generic Radar Simulator), open new perspectives to the Radar Simulation world for EW Systems evaluation and other purposes.

Since it is not possible in an Electronic Warfare Evaluation Test Range to assess the System Under Test (SUT) effects on real enemy radars, the only way to test the SUT is to use a "programmable radar simulator" capable to emulate them. This is done by the E-PRS using a real radar digital receiver, waveform generator and programmable signal and data processor. This method, unlike the SW simulation approach, takes in proper account the response and limitations of a real HW processing including non-linearity, distortion, saturation, etc.. This approach is commonly defined as "Hardware in The Loop" (HWIL) simulation system. Moreover with this method it is possible to "play-back" the same simulation (originally run in real time)and analyze the data collected for making deep analysis on the jammer effectiveness or for training purposes.
The E-PRS can simulate ground based Radars, airborne and ship-borne Radars, missile seekers (active and semi-active).
The targets and other emitters/scatterers can be generated at RF level by means of a module called Eldes Radar Environment Generator (E-REG) or using COTS components supplied by third parties. The E-REG receives from the external Scenario Simulator the position and the trajectory of the platforms and generates the target skin echoes accordingly.
The supervisory control of the whole system and simulation, including also the Scenario Control is managed by a computer with adequate software and physical interfaces which also provides the display and data analysis functionalities, as well as hosting the user programmed radar model data base.
Multiple SUTs can be tested at the same time with the proper HW and SW E-PRS configuration.
The E-PRS is also a valuable support for Radar System engineering to test the effectiveness of new radar and ECCM techniques.

Operation principles
The E-PRS TX pulse is generated by an arbitrary waveform generator; the waveform could be simple or complex to implement many types of pulse compression techniques (Chirp, Barker, etc.).
The SUT receives the pulses generated by the E-PRS, weighted by the simulated antenna pattern. Starting from this input, it generates the jammer signal (SPJ or SOJ) that, together with the target skin echo (from E-REG) is injected in the RF or IF input (according to the system architecture)of the E-PRS.
By means of the RX antenna simulator the receiving antenna weighting is applied and the signal goes to the digital receiver for the analog to digital and base-band conversions. The resulting signal is then processed through the user programmable matched filter that implement the proper filtering according to the actual TX waveform.
After the filtering, the signal samples are sent to a powerful HPC (based on an array of Intel Xeon processors) to implement the desired radar signal and data processing according to the built-in or user generated algorithms library.
The receiver will react exactly as the one of a real radar (of the selected type) providing to the user all the data to evaluate the real effects of the SUT on Radar detection and tracking.

System Architecture
The E-PRS, see block diagram, is composed by the following functional blocks:
Microwave receiver
Digital receiver (4 or more channels)
Microwave Transmitter
Programmable Signal and Data Processors.
Radar TX and RX Antenna Simulator
RF/IF Target(s) / Chaff / Clutter Generator. (E-REG or others)
Software Programming environment (Framework).
Display and Data Collection/Analysis System

Software Features
E-PRS Framework
An advanced programming mode to create radar models using a "friendly" high level graphic user interface called E-PRS Framework is available. With this tool the user can generate a radar model according to his needs, simply using the functional library provided with the system.
The other way to program a radar model is to write the algorithms using the C/C++ language. In this way the user can also extend the basic E-PRS library and then simulate all possible radars.
Using the framework, further to the platform and radar type, the operator can choose all the radar operational parameters like:
Matched Filter: Barker, bi-phase and quad-phase, CHIRP.
TX parameters (PRF, Pulse, Stagger, Jitter, MOP, CW, etc.)
MTI-AMTI-MTD processing
Target Glint
Doppler Channel
Tracking Loops: Range, Angle, Velocity
Ambiguity Resolver
Antenna type and radiation pattern

DCA (Data Collection and Analysis)
This software tool, supplied with E-PRS, allows the user to collect all the main events during the simulation and retrieve the information on success/not success of the ECM generated by the SUT. The DCA records all the macro events (i.e. Tracking, track-lost, tracking errors, etc...) in addition to the scenario and target info.
All the simulation can be eventually played-back for training purposes using different display modes (PPI, A, B, C scope).
Attached documents
Size: 454,04 KB
Size: 2,66 MB
Download E-PRS Presentation

[Realizzazione siti web www.sitoper.it]
Request the product
Enter your email address to be notified when the product will be available again.

Request for availability sent
Availability request not sent